Completing the consist
As mentioned in the last post, heavyweight parlor cars are the one missing type of rolling stock needed to complete model passenger train consists on the layout.
The heavyweight parlor cars GREAT REPUBLIC and AUBURN were assigned to the Berkshire Line of the New Haven Railroad during 1957.
Both cars were equipped with Electro-mechanical air-conditioning that would not require icing en route where none may be available during the warmer months on the Berkshire Line during that era. See excerpt from the 1957 passenger train consist list below.
Although no photographic evidence has surfaced to date of either car on the Berkshire Line, the GREAT REPUBLIC was the one parlor car most mentioned by those who witnessed that era first hand will be the car modeled first.
Choosing a base modeling core
There are no accurate era correct RTR models of the specific heavyweight Pullman prototypes that were assigned to the Berkshire Line during the era of the layout. Starting with a Pullman kit for use as a base modeling core combined with aftermarket styrene, resin or brass parts will help facilitate a conversion to an accurate parlor car.
A Branchline Trains Pullman sleeper kit will be used for a base modeling core, this choice remains consistent with other Pullman cars already built for the layout.
Unfortunately, kits and some parts used during this build are no longer available from the original manufacturer but may still be found elsewhere.
Car sides
There are some interesting challenges in converting the Branchline Trains sleeper core to an accurate model of the GREAT REPUBLIC, Pullman Plan #4001.
The first step will be correcting the layout of the windows on both car sides to a Plan #4001 arrangement.
A floor plan for Pullman Plan #4001 is available on the internet from the Pullman Digital Collection at the Newberry Library, this is an invaluable source for the correct spacing and dimensions of the windows and overall layout of the interior.
A similar method used to replace the windows when building the DUDLEY is used again for the GREAT REPUBLIC.
Both car sides from the core Branchline Trains Pullman kit had the complete window area removed leaving only the top and bottom portions of the sides behind. The vestibule doors were also removed from the sides although shown taped in place for the photo below.
Above, one side of the Plan #4001 replacement window arrangement with the appropriate sized styrene windows from New England Rail Service and styrene filler panels referring to the floor plan from the Newberry Library as a guide.
A temporary jig for gluing the widows to the car sides is formed with styrene pieces glued to the top and bottom of opposite sides of an aluminum block this adding up to a total measurement exactly equal to the inside width between the kits car sides when snapped into place. The larger stack of styrene pieces in the middle of the block will provide a work surface to inset the replacement windows and panels to a consistent depth while gluing them in place.
Sliding this temporary jig along the floor from window to window while gluing the windows and filler panels in place below.
A bottle of Tamiya extra thin cement with brush applicator worked very well for this procedure.
A completed pair of Plan #4001 sides below.
Roof
The roof is the most interesting challenge during this conversion.
The GREAT REPUBLIC has a wide clerestory roof making it necessary to replace both the narrow clerestory roof and matching pedimented car ends from the core Branchline Trains kit. A cast resin wide clerestory roof void of any venting detail on both sides of the clerestory and matching resin pedimented car ends from Tom Madden will replace the Branchline Trains parts.
The most difficult challenge and the one that held back the build of this car for considerable time is the exterior roof air conditioning duct. This duct is the type that rises vertically approximately 12" from the car side before curving to meet the top of the clerestory; if there is a proper nomenclature for this type of duct it is unknown to me. A cropped photo of a converted NH parlor to coach below is the best example on hand to illustrate this type of A/C duct.
There is no known HO scale aftermarket part for this type of duct. Scratch building one over a curved A/C duct using the test method below was considered, but the project stalled here.
A gifted resin roof for possible use with this build that had the correct type of ducts on both sides of the clerestory was the motivation to restart this stalled project.
Neither of these ducts from the donor roof were long enough to replicate the length of the one side only duct on the GREAT REPUBLIC. This turned out to be a positive by being able to cut out both ducts from the donor roof, adjust the overall length of the donor duct by splicing partial segments of these ducts together to the correct overall length needed for the GREAT REPUBLIC.
The photo below shows the wide clerestory resin roof to be used with a cut out to receive the donor duct with the two duct parts now spliced together.
These resin pieces need to be glued together with an ACC type adhesive. The issue with ACC is the quick drying time and the one shot to get it correct over the long length of the duct, and not wanting to mar the outside to be seen top surface.
The solution was to ACC .005" styrene pieces to the underside joining the duct to the roof, starting on one end then the opposite end, then the center, following outward from center. This worked well with good tight joints with no glue maring the exterior seen surface.
This photo shows all that remains of the Branchline Trains base plate/chassis.
The car ends have been removed for the replacement wide clerestory resin car ends to be glued in place with ACC.
The white styrene pads glued to all four vertical uprights make up for the difference in thickness between the Branchline car sides and the thinner replacement windows, this offers a consistent surface bottom to top when gluing on the sides during final assembly.
The notch cut into the far upright is to clear the saloon window that is very close to the interior vestibule wall, the same notch is on the opposite end for the other saloon.
The floor will be covered first with the steel weight supplied with the kit then a styrene floor to mount the interior details.
Temporally assembling the sides, roof, car ends and doors for a test fit, looks like all will fit together well.
To finish this assembly for painting, the visible end joints of the ducts will be smoothed with a lightweight catalyzed automotive filler, rivet decals below the window belt rail to match the window rivet pattern above and clerestory vents and fans to match the prototype will be applied.
Paint
Once the needed Archer rivet decals were applied, the car sides, vestibule doors and car ends were painted Badger Model Flex New Haven Pullman green #16-180, this color is a good match with the factory applied Pullman green on Rapido Osgood-Bradley "American Flyer" coaches already on the layout offering a good color consistency amongst the passenger car roster.
The painted pair of sides with Bethlehem Car Works decals,
and the with the roof painted black.
Seating
The rotating parlor car seats are from a donor Walthers parlor car. Not knowing what color they were in 1957, the same dark blue used on other NH passenger cars on the layout roster was applied. The antimacassars are small pieces of white decal applied over the top of the chair backs.
The 34 parlor car seats mounted on the car floor, arraigned in a similar pattern as the drawing from the Newberry Library. The one smaller chair to the right is the Porter's chair.
All the walls/partitions, some from the Walthers car and some scratch built, were added later but unfortunately no photo taken.
Finished car GREAT REPUBLIC
The details to finish the car ends, vestibule steps, hand grabs and trucks all are from the Branchline Trains core kit.
The roof clerestory vents and fans all are Tom Madden resin castings.
All underbody equipment is an assortment of details from the Branchline Trains core kit, New England Rail Service, Tom Madden resin castings, Walthers, Cal Scale, or scratch built; all equipment is located on the underbody as best as could be determined from prototype photos.
Finally a heavyweight parlor car for the Berkshire Line layout!
The elegant prototype parlor car GREAT REPUBLIC is still in service to this day at
The Valley Railroad in Essex Connecticut, see and ride in it if you can!
No comments:
Post a Comment